Effects of poly(butylene succinate) and calcium carbonate on the physical properties of plasticized poly(vinyl chloride)

Authors

  • Anyaporn Boonmahitthisud Department of Science, Faculty of Science, Chulalongkorn University
  • Phasawat Chaiwutthinan Department of Materials Science, Faculty of Science, Chulalongkorn University
  • Sitthipong Samutthong Department of Materials Science, Faculty of Science, Chulalongkorn University
  • Onusa Saravari Department of Materials Science, Faculty of Science, Chulalongkorn University
  • Saowaroj Chuayjuljit Department of Materials Science, Faculty of Science, Chulalongkorn University

Keywords:

Poly(vinyl chloride), Diisononyl phthalate, Poly(butylene succinate), Calcium carbonate, Physical properties

Abstract

In this studypoly(butylene succinate) (PBS) , a polymeric plasticizer,  was partially replaced a conventional plasticizer, diisononyl phthalate (DINP) to avoid the plasticizer loss from poly(vinyl chloride) (PVC) overtime for various service conditions and to obtain a long-term plasticizer retention in the flexible PVC products. The plasticized PVC samples were prepared by melt mixing on a two roll mill, followed by compression molding. The mechanical properties (tensile properties, tear strength and hardness), thermal stability and morphology of the 20/20 phr (parts by weight per hundred parts of resin) DINP/PBS-plasticized PVC were evaluated and compared with those of the 40 phr DINP-plasticized PVC. The tensile strength, Young’s modulus, tear strength, hardness and thermal stability were found to be improved, while the elongation at break was decreased as a result of the partial replacement of DINP with PBS in the plasticized PVC. Moreover, the DINP/PBS-plasticized PVC composites filled with varied loadings of CaCO3 (2.5, 5, 7.5 and 10 phr) showed an increase in the elongation at break, Young’s modulus and thermal stability in a dose-dependent manner, while the tensile strength, tear strength and hardness were unaffected by the increasing amount of CaCO3. The morphology of the composites observed by scanning electron microscopy showed a number of voids on the fractured surface of the plasticized PVC due to the pulling out CaCO3 particles, caused by the low interfacial adhesion between filler and polymer.

Downloads

Download data is not yet available.

References

Marathe, D.S. and Joshi, P.S. (2009). Characterization of highly filled wood flour-PVC composites: morphological and thermal studies. J. Appl. Polym. Sci. 114(1) : 90-96.

Shah, B.L. and Shertukde, V.V. (2003). Effect of plasticizers on mechanical, electrical, permanence, and thermal properties of poly(vinyl chloride). J. Appl. Polym. Sci. 90(12) : 3278-3284.

Das, G. and Karak, N. (2012). Epoxidized Mesua ferrea L. seed oil-plasticized thermostable PVC and PVC-clay nanocomposites. J. Vinyl Addit. Technol. 18(3) : 168-177.

Garcia-Quesada, J.C., Pelaez, I., Akin, O. and Kocabas, I. (2012). Processability of PVC plastisols containing a polyhydroxybutyratepolyhydroxyvalerate copolymer. J. Vinyl Addit. Technol. 18(1) : 9-16.

Pielichowski, K. and Świerz-Motysia, B. (2006). Influence of polyesterurethane plasticizer on the kinetics of poly(vinyl chloride) decomposition process. J. Therm. Anal. Cal. 83(1) : 207-212.

Pena, J.R., Hidalgo, M. and Mijangos, C. (2000). Plastification of poly(vinyl chloride) by polymer blending. J. Appl. Polym. Sci. 75(10) : 1303-1312.

Li, X., Xiao, Y., Wang, B., Tang, Y., Lu, Y. and Wang, C. (2012). Effects of poly(1,2-propylene glycol adipate) and nano-CaCO3 on DOP migration and mechanical properties of flexible PVC. J. Appl. Polym. Sci. 124(2) : 1737-1743.

Ambrogi, V., Brostow, W., Carfagna, C., Pannico, M. and Persico, P. (2012). Plasticizer migration from cross-linked flexible PVC : Effects on tribology and hardness. Polym. Eng. Sci. 52(1) : 211-217.

Tüzüm Demir, A.P. and Ulutan, S. (2013). Migration of phthalate and non-phthalate plasticizers out of plasticized PVC films into air. J. Appl. Polym. Sci. 128(3) : 1948-1961.

Li, H., Wang, L., Song, G., Gu, Z.H., Li, P., Zhang, C.H. and Gao, L. (2010). Study of NBR/PVC/OMMT nanocomposites prepared by mechanical blending. Iran. Polym. J. 19(1) : 39-46.

Sunny, M.C., Ramesh, P. and George, K.E. (2004). Use of polymeric plasticizers in polyvinyl chloride to reduce conventional plasticizer migration for critical applications. J. Elastom. Plast. 36(1) : 19-31.

Ha, C.S., Kim, Y., Lee, W.K., Cho, W.J. and Kim, Y. (1998). Fracture toughness and properties of plasticized PVC and thermoplastic polyurethane blends. Polymer. 39(20) : 4765-4772.

Pita, V.J.R.R., Sampaio, E.E.M. and Monteiro, E.E.C. (2002). Mechanical properties evaluation of PVC/plasticizers and PVC/thermoplastic polyurethane blends from extrusion processing. Polym. Test. 21(5) : 545-550.

Deanin, R.D. and Zheng-Bai, Z. (1984). Polycaprolactone as a permanent plasticizer for pol(vinyl chloride). J. Vinyl Addit. Technol. 6(1) : 18-21.

Rusu, M., Ursu, M. and Rusu, D. (2006). Poly(vinyl chloride) and poly(ε-caprolactone) blends for medical use. J. Thermoplast. Compos. Mater. 19(2) : 173-190.

Rahim, M.N.M., Ibrahim, N.A., Sharif, J. and Wan Yunus, W.M.Z. (2010). Mechanical and thermal properties of poly(vinyl chloride) /poly(butylene adipateco-terephthalate) clay nanocomposites. J. Reinf. Plast. Compos. 29(21) : 3219-3225.

Ratnam, C.T. and Zaman, K. (1999). Stabilization of poly (vinyl chloride)/epoxidized natural rubber (PVC/ENR) blends. Polym. Degrad. Stabil. 65(1) : 99-105.

Thomas, N.L. (2004). Alloying of poly(vinyl chloride) to reduce plasticizer migration. J. Appl. Polym. Sci. 94(5) : 2022-2031.

Kim, H.S., Lee, B.H., Lee, S., Kim, H.J. and Dorgan, J.R. (2011). Enhanced interfacial adhesion, mechanical, and thermal properties of natural flour-filled biodegradable polymer bio-composites. J. Therm. Anal. Calorim. 104(1) : 331-338.

Zhiu, J., Wang, X., Hua, K., Duan, C., Zhang, W., Ji, J. and Yang, X. (2013). Enhanced mechanical properties and degradability of poly(butylene succinate) and poly(lactic acid) blends. Iran. Polym. J. 22(4) : 267-275.

Kanemura, C., Nakashima, S. and Hotta, A. (2012). Mechanical properties and chemical structures of biodegradable poly(butylene -succinate) for material reprocessing. Polym. Degrad. Stabil. 97(6) : 972-980.

Ahamad, A., Patil, C.B., Gite, V.V. and Hundiwale, D.G. (2012). Evaluation of the synergistic effect of layered double hydroxides with micro-and nano-CaCO3 on the thermal stability of polyvinyl chloride composites. J. Thermoplast. Compos. Mater. 26(9) : 1249-1259.

Sombatsompop, N., Teptim, K., Chaochanchaikul, K., Thongpin, C. and Rosarpitak, V. (2008). Improvement of structural and thermal stabilities of PVC and wood/PVC composite by Zn and Pb stearates and zeolite. J. Macromol. Sci. Pure Appl. Chem. 45(7) : 534-541.

Sajjadi Jazi, S.H., Nasr Esfahany, M. and Bagheri, R. (2012). Investigation of the addition of nano-CaCo3 at dry mixing or onset of fusion on the dispersion, torque, and mechanical properties of compounded PVC. J. Vinyl Addit. Technol. 18(3) : 153-160.

Downloads

Published

2014-12-11

How to Cite

[1]
A. Boonmahitthisud, P. Chaiwutthinan, S. Samutthong, O. Saravari, and S. Chuayjuljit, “Effects of poly(butylene succinate) and calcium carbonate on the physical properties of plasticized poly(vinyl chloride)”, J Met Mater Miner, vol. 24, no. 2, Dec. 2014.

Issue

Section

Original Research Articles

Most read articles by the same author(s)

1 2 > >>