Effect on mechanical properties of aluminium alloy composites on adding ash as reinforcement material

Authors

  • Mohd Zafaruddin Khan Department of Mechanical Engineering, University Polytechnic Integral University
  • Mohd Anas Department of Mechanical Engineering, Integral University, Lucknow, Uttar Pradesh
  • Ather Husain Department of Mechanical Engineering, Integral University, Lucknow
  • Md Irshadul Haque Mechanical Engineer Mushrif trading & contracting Co
  • Kamran Rasheed Department of Mechanical Engineering, Integral University, Lucknow

Keywords:

Aluminium Matrix Composite, Fly ash, Bagasse ash, Mechanical Properties

Abstract

To produce Al-matrix cast particle composites, wettability of the ceramic particles by liquid Al is essential. To improve wettability of the solution, few elements such as Mg and Si are added into Al melt to incorporate the ceramic particles. The present investigation has been focussed on the utilization of abundant available industrial waste such as fly ash and bagasse ash in useful manner by dispersing it into Eutectic Al-Si alloy LM6 Containing 10.58% Si to produce composites by liquid casting route. The mechanical properties such as Brinell Hardness and Ultimate tensile strength has been investigated. The test results of the mechanical properties have indicated that the ultimate tensile strength varies from 112.6 kN/mm­­­­2 to 180 kN/mm2 with maximum value at 10wt % fly ash +10wt % bagasse ash and hardness varies from 52 BHN to 80 BHN with maximum value at 10wt% fly ash  + 10wt% bagasse ash as reinforcement in the matrix metal. It was concluded that 10wt% fly ash +10wt% bagasse ash can be used as reinforcement in aluminium composites and the produced composites could be used in automobile industry for the production of lighter & strong engine blocks, pistons and other components.      

Downloads

Download data is not yet available.

References

Singla, M., Dwivedi, D., Singh, L. and Chawla, V. (2009). Development of aluminium based silicon carbide particulate metal matrix composite. J. Miner. Mater. Character. Eng. 8(6) : 455-467.

Aigbodion, V.S., Hassan, S.B., Dauda, E.T. and Mohammed, R.A. (2011). Experimental study of ageing behaviour of Al-Cu-Mg/bagasse ash particulate composites. Journal of Tribologyin industry. 33(1) : 28-35.

Verma, D., Gope, P.C., Maheshwari, M.K. and Sharma, R.K. (2012). Bagasse fiber composites-A review. J. Mater. Environ. Sci. 3(6) : 1079-1092.

A.P.S.V.R. Subrahmanyam, G. Narsaraju and Srinivasa Rao, B. (2015). Effect of rice husk ash and fly ash reinforcements on microstructure and mechanical properties of aluminium alloy (AlSi10Mg) Matrix composites. IJAST. 76 : 1-8.

Mohana Rao, D. and Bapi Raju Bandam M.E. (2014). Preparation and characterization of Al-Fly ash metal matrix composite by stir casting method. IJISME. 3(1) : 1-5.

Usman, A. M., Raji, A., Hassan, M. A. and Waziri, N. H. (2014). A comparative study on the properties of Al-7% Si-Rice husk ash and Al-7% Si-Bagasse ash composites produced by stir casting. IJES. 3(8) : 1-7.

Singla, Deepak and Mediratta, S.R. (2013). Evaluation of mechanical properties of Al 7075-fly ash composite material. IJIRSET. 2(4) : 951-959.

Lokesh, G. N., Ramachandra, M., Mahendra, K.V., Sreenith, T. (2013). Characterization of Al-Cu alloy reinforced fly ash metal matrix composites by squeeze casting method. IJEST. 5(4) : 71-79.

Madakson, P.B., Yawas, D.S. and Apasi, A. (2012). Characterization of coconut shell ash for potential utilization in metal matrix composites for automotive applications. IJEST. 4(3) : 1190-1198.

Mahendra, K.V. and Radhakrishna, K. (2007). Fabrication of Al-4.5% Cu alloy with fly ash MMC and its characterization. Mater. Sci. Poland. 25(1) : 57-68.

Downloads

Published

2015-12-30

How to Cite

[1]
M. . Z. Khan, M. Anas, A. Husain, M. I. Haque, and K. Rasheed, “Effect on mechanical properties of aluminium alloy composites on adding ash as reinforcement material”, J Met Mater Miner, vol. 25, no. 2, Dec. 2015.

Issue

Section

Original Research Articles