Mechanical property improvement of UPE resin from glycolyzed PET with commercial UPE resin

Authors

  • Thidarat Limpiti Faculty of Science, Chulalongkorn University
  • Pranut Potiyaraj Faculty of Science, Chulalongkorn University, National Center of Excellence for Petroleum, Petrochemicals, and Advanced Materials, Chulalongkorn University

Keywords:

Petrography, Recycling, Glycolysis, Unsaturated polyester

Abstract

The aim of this research paper is to improve mechanical properties of cured unsaturated polyester (UPE) resin prepared from glycolyzed PET by mixing with a commercial UPE resin. Postconsumer PET bottles were depolymerized by glycolysis reaction in excess propylene glycol at 190ºC in the presence of zinc acetate as a catalyst. The glycolyzed product was polyesterified with maleic anhydride and mixed with styrene monomer in order to obtain UPE resin. The prepared UPE resin was mixed with a commercially available general purpose grade UPE resin at various ratios. The mixed resins were cured using methyl ethyl ketone peroxide and cobalt octoate. Comparing between the prepared and commercial resins, it is most likely that the cured product from prepared resin possessed a higher crosslink density than the cured commercial resin. The results showed that the hardness of cured resin prepared from glycolyzed PET was slightly higher than that of the cured commercial resin. The addition of commercial resin did not affect the hardness of mixed resins. The impact strength and flexural strength increased as the amount of commercial resin increased. However, at higher than 60% by weight of the commercial resin, the improvement was leveled off.

Downloads

Download data is not yet available.

References

Awaja, F. and Pavel, D. 2005. Recycling of PET. Eur. Polym. J. 41 : 1453-1477.

Paszun, D. and Spychaj, T. 1997. Chemical recycling of poly(ethylene terephthalate). Ind. Eng. Chem. Res. 36 : 1373-1383.

Baliga, S. and Wong, W.T. 1989. Depolymerization of poly(ethylene terephthalate) recycled from post-consumer soft-drink bottles. J. Polym. Sci. : Part A, Polym. Chem. 27 : 2071-2082.

Vaidya, U.R. and Nadkarni, V.M. 1987. Unsaturated polyester resins from poly(ethylene terephthalate) waste. 1. Synthesis and characterization. Ind. Eng. Chem. Res. 26 : 194-198.

Vaidya, U.R. and Nadkarni, V.M. 1988. Unsaturated polyester resins from poly(ethylene terephthalate) waste. 2. Mechanical and dynamic mechanical properties. Ind. Eng. Chem. Res. 27 : 2056-2060.

Saravari, O., Vessabutr, B. and Pimpan, V. 2004. Synthesis of urethane oils from waste poly (ethylene terephthalate) bottles. J. Appl. Polym. Sci. 92 : 3040-3045.

Ghaemy, M. and Mossaddegh, K. 2005. Depolymerisation of poly(ethylene terephthalate) fibre wastes using ethylene glycol. Polym. Degradation and Stab. 90 : 570-576.

Potiyaraj, P., Klubdee, K. and Limpiti, T. 2007. Physical properties of unsaturated polyester resin from glycolyzed PET fabrics. J. App. Polym. Sci. 104 : 2536- 2541.

Öztürk, Y. and Güçlü, G. 2004. Unsaturated polyester resins obtained from glycolysis products of waste PET. Polym.-Plast. Technol. Eng. 43 : 1539-1552.

Pardal, F.and Tersac, G. 2006. Comparative reactivity of glycols in PET glycolysis. Poly. Degradation Stab. 91 : 2567-2578.

Pimpan, V., Sirisook, R. and Chuayjuljit, S. 2003. Synthesis of unsaturated polyester resin from postconsumer PET bottles: Effect of type of glycol on characteristics of unsaturated polyester resin. J. Appl. Polym. Sci. 88 : 788-792.

Aslan, S., Immirzi, B., Laurienzo, P., Malinconico, M., Martuscelli, E., Volpe, M.G., Pelino, M. and Savini, L. 1997. Unsaturated polyester resins from glycolysed waste polyethyleneterephthalate: synthesis and comparison of properties and performance with virgin resin. J. Mater. Sci. 32 : 2329-2336.

DeMaio, A.J. 1991. Engineering high performance thermoset polyesters from PET. RecyclingPlas VI Conference, Plastics Recycling as a Future Business Opportunity, Washington DC : 58-71.

Suh, D.J., Park, O.O. and Yoon, K.H. 2000. The properties of unsaturated polyester based on the glycolyzed poly(ethylene terephthalate) with various glycol compositions . Polymer. 41 : 461-466 .

Zuiderduin, W.C.J., Westzaan, C., Huétink, J. and Gaymans, R.J. 2003. Toughening of polypropylene with calcium carbonate particles. Polymer. 44 : 261-275.

Abdel-Azim, A.A. 1995. Mechanical properties and curing characteristics of unsaturated polyesters synthesized for large casting. Polym. Bull. 35 : 229-236.

Mujika, F., Carbajal, N., Arrese, A. and Mondragon, I. 2006. Determination of tensile and compressive moduli by flexural tests. Polym. Test. 25 : 766-771.

Downloads

Published

2017-04-15

How to Cite

[1]
T. Limpiti and P. Potiyaraj, “Mechanical property improvement of UPE resin from glycolyzed PET with commercial UPE resin”, J Met Mater Miner, vol. 19, no. 1, Apr. 2017.

Issue

Section

Original Research Articles