Microstructure and mechanical properties of EN AW 6082 aluminium alloy prepared by equal-channel angular pressing

Authors

  • Martin Fujda Department of Materials Science, Faculty of Metallurgy, Technical University of Košice
  • Tibor Kvačkaj Department of Metal Forming, Faculty of Metallurgy, Technical University of Košice

Keywords:

EN AW 6082 aluminium alloy, severe plastic deformation, ECAP, mechanical properties, microstructure, deformation strengthening, precipitation

Abstract

The mechanical properties and microstructure of EN AW 6082 aluminium alloy subjected to severe plastic deformation (SPD) and natural ageing are compared with those of extruded and artificially aged state (initial state) and quenched state of alloy after solution annealing. Quenched state of alloy was deformed at room temperature by equal channel angular pressing (ECAP) following route C up to three passes. Polyedric microstructure of quenched state was considerably changed by SPD. Deformation bands with different amount of deformation were observed in microstructure of ECAPed state, which indicated non-uniform deformation across the cross-section of ECAPed specimen. Ultimate tensile strength (UTS) and especially yield strength (0.2% YS) were considerably increased by SPD, but plasticity was decreased. Increase of strength of ECAPed state was first of all evoked by the deformation strengthening.

Downloads

Download data is not yet available.

References

Humphreys, F. J. and Hatherly, M. 1996. Recrystallization and Related Annealing Phenomena. Oxford : Elsevier : 205

Valiev, R. Z., Krasilnikov, N. A. and Tsenev, N. K. 1991. Mater. Sci. Eng. A 137 : 3317.

Horita, Z., Fujinami, T., Nemoto, M. and Langdon, T. G. 2001. Improvement of mechanical properties for AI alloys using equal-channel angular pressing. J.Mater. Process. Technol. 117 : 288 – 292.

Furukawa, M., Horita, Z., Nemoto, M., Valiev, R. Z. and Langdon, T. G. 1996. Mater. Character. 37 : 277.

Valiev, R. Z., Estrin, Y., Horita, Z. and Langdon, T. G., Zehetbauer, M., Zhu, Y.T: JOM. 58 : 33.

Lowe, T.C., Valiev, R.Z. 2000. Investigations and Applications of Severe Plastic Deformation. Kluwer : Dordrecht, the Netherlands.

Zehetbauer, M. J. and Valiev, R. Z. 2004. Nanomaterials by Severe Plastic Deformation. Weinheim, Wiley-VCH.

Horita, Z. 2005. Nanomaterials by Severe Plastic Deformation. Uetikon-Zurich : Trans Tech Publications.

Segal, V. M., Reznikov, V.I., Dobryshevskiy, A. E. and Kopylov, V. I. 1981. Rus. Metall. 1 : 99.

Islamgaliev, R. K., Yunusova, N. F., Sabirov, I. N., Sergueeva, A. V. and Valiev, R. Z. 2001. Deformation behaviour of nanostructures aluminum alloy processed by severe plastic deformation. Mater. Sci. Eng. A – Structural Materials Properties Microstructure and Processing. 319 : 877 – 881.

Saito, Y., Utsunomiya, H., Tsuji, N. and Sakai, T. 1999. Novel ultra-high straining process for bulk materials–Development of the accumu- lative roll–bonding (ARB) process. Acta Materialia. 47(2) : 579 – 583.

Zhu, Y. T., Jiang, H., Huang, J. Y. and Lowe, T.C. 2001. Mater. Trans A. 32 : 1559.

Kim, W. J. and Wang, J. Y. 2007. Microstructure of the post-ECAP aging processed 6061 AI alloys. Mater. Sci. Eng. A-Structural Materials Properties Microstructure and Processing. 464(1-2) : 23 – 27.

Cherukuri, B., Nedkova, T. S. and Srinivasan, R. 2005. A comparison of the properties of SPD-processed AA-6061 by equal-channel angular pressing, multi-axial compressions/ forgings and accumulative roll bonding. Mater. Sci. Eng. A-Structural Materials Properties Microstructure and Processing. 410 : 394 – 397.

Werenskiold, J. C. and Roven, H. J. Microstructure and texture evolution during ECAP of an AIMgSi alloy: Observations, mechanisms and modelling. 2005. Mater. Sci. Eng. A-Structural Materials Properties Micro-structure and Processing. 410 – 411 : 174 – 177.

Roven, H. J., Nesboe, H., Werenskiold, J. C. and Seibert, T.2005. Mechanical properties of aluminium alloys processed by SPD: Com-parison of different alloy systems and possible product areas. Mater. Sci. Eng. AStructural Materials Properties Microstructure and Processing. 410 - 411 : 426 – 429.

Leo, P., Cerri, E., De Marco, P. P. and Roven, H. J. 2007. Properties and deformation behaviour of severe plastic deformed alumi-nium alloys. J. Mater. Process. Technol. 182(1-3) : 207 – 214.

Zrník, J., Nový, Z., Kvačkaj, T., Bernášek, V, Kešner, D. and Slámová, M. 2004. Acta Metall. Slovaca. 10 : 277.

Iwahashi, Y., Wang, J., Horita, Z., Nemoto, M. and Langdon, T. G. 1996. Scr. Mater. 35 : 143.

Fujda, M. and Vojtko, M.2007. Acta Metall. Slovaca, 13, SI, 1 : 585.

Parson, N., Hankin, J., Hicklin, K. and Jowett, C. 2000. Proceedings of the 7th International Aluminum Extrusion Technology Seminar, vol. 1. Washington, DC : Aluminum Association : 1.

Downloads

Published

2017-04-23

How to Cite

[1]
M. Fujda and T. Kvačkaj, “Microstructure and mechanical properties of EN AW 6082 aluminium alloy prepared by equal-channel angular pressing”, J Met Mater Miner, vol. 17, no. 2, Apr. 2017.

Issue

Section

Original Research Articles

Most read articles by the same author(s)