Novel thermoplastic vulcanizates based on polyamide 12 blends: Influence of modified devulcanized natural rubber gloves on properties of the blends

Authors

  • Sitisaiyidah Saiwari Department of Rubber Technology and Polymer Science, Faculty of Science and Technology, Prince of Songkla University
  • Boripat Sripornsawat Department of Rubber Technology and Polymer Science, Faculty of Science and Technology, Prince of Songkla University
  • Nabil Hayeemasae Department of Rubber Technology and Polymer Science, Faculty of Science and Technology, Prince of Songkla University

Keywords:

Maleated Devulcanized Natural Rubber Gloves (MDNRG), Devulcanized Natural Rubber Gloves (DNRG), Polyamide-12 (PA-12), Thermoplastic vulcanizates (TPVs)

Abstract

Alternative application for utilization of recycled rubber is extended in thermoplastic elastomer. Thermoplastic vulcanizates (TPVs) from blends of polyamide 12 (PA 12) and devulcanized rubber from waste of natural rubber gloves (DNRG) have been successfully prepared. The TPVs remarkably exhibit superior elasticity compared to the original PA 12.  Further improvement of physical properties of the TPVs has been elaborated by introducing maleated DNRG (MDNRG). The grafting efficiency of maleic anhydride onto the MDNRG backbone was confirmed by FTIR technique. The MDNRG/PA 12 TPVs exhibited greater stiffness and damping factor compared to the DNRG/PA 12 TPVs. This is attributed to chemical interaction between polar functional groups in the PA 12 molecules and anhydride groups in the MDNRG molecules which have been proved by ATR-FTIR and TSSR techniques. Moreover, the interfacial interaction facilitates higher interfacial adhesion between the both phases consequently results in the significant improvement of the MDNRG/PA 12 TPVs mechanical and elastic properties. This is in good agreement to the morphology of the blends. It is verified that the smaller micron-sized vulcanized rubber domains dispersed in the PA 12 matrix is found in the MDNRG/PA 12 TPVs compared to the DNRG/PA 12 TPVs.

Downloads

Download data is not yet available.

References

K. Chatterjee and K. Naskar, “Development of thermoplastic elastomers based on maleated ethylene propylene rubber (m-EPM) and polypropylene (PP) by dynamic vulcanization,” Express Polymer Letters, vol. 1, pp. 527-534, 2007.

M. R. Abadchi, A. J. Arani, and H. Nazockdast, “Partial replacement of NR by GTR in thermoplastic elastomer based on LLDPE/NR through using reactive blending: Its effects on morphology, rheological, and mechanical properties,” Journal of Applied Polymer Science, vol. 115, pp. 2416-2422, 2010.

L. Meszaros, M. Fejos, and T. Barany, “Mechanical properties of recycled LDPE/ EVA/ground tyre rubber blends: Effects of EVA content and post irradiation,” Journal of Applied Polymer Science, vol. 125, pp. 512- 519, 2012.

M. M. Hassan, N. A. Badway, M. Y. Elnaggar, and E. A. Hegazy, “Synergistic effect of gamma radiation and peroxide on dynamic vulcanization of thermoplastic vulcanizes based on (de-vulcanized rubber)/polypropylene,” Journal of Vinyl and Additive Technology, vol. 20, pp. 168-176, 2014.

B. Sripornsawat, A. Kaesaman, and C. Nakason, “Thermoplastic Natural Rubber of Co-Polyamide: Effect of Blend Ratios on Mechanical, Swelling, Dynamic and Morphological Properties,” Advanced Materials Research, vol. 844, pp. 89-92, 2014.

H. Heping, L. Sidong, and P. Zheng, “Preparation and study of epoxidized natural rubber,” Journal of Thermal Analysis and Calorimetry, vol. 58, pp. 293-299, 1999.

M. Subhra, P. G. Mukundab, and G. B. Nando, “Thermal analysis of blends of poly(ethylene-co-acrylic acid) (PEA) and epoxidised natural rubber (ENR),” Polymer Degradation and Stability, vol. 50, pp. 21-28, 1995.

C. Nakason, A. Kaesaman, and P. Supasanthitikul, “The grafting of maleic anhydride onto natural rubber,” Polymer Testing, vol. 23, pp. 35-41, 2004.

C. Nakason, S. Saiwari, and A. Kaesaman, “Rheological, thermal and morphological properties of maleated natural rubber and its reactive blending with poly(methyl methacrylate),” Polymer Testing, vol. 25, pp. 656-667, 2006.

N. Hinchirana, W. Lertweerasirikun, W. Poonsawad, G. L. Rampel, and P. Prasassarakich, “Hydrogenated natural rubber blends: aspect on thermal stability and oxidative behavior,” Journal of Applied Polymer Science, vol. 113, pp. 1566-1575, 2009.

W. Arayapranee, and G. L. Rempel, “Morphology and mechanical properties of natural rubber and styrene-grafted natural rubber latex compounds,” Journal of Applied Polymer Science, vol. 109, pp. 1395-1402, 2008.

S. Salaeh, T. Banda, V. Pongdong, S. Wießner, A. Das, and A. Thititammawong, “Compatibilization of poly(vinylidene fluoride)/natural rubber blend by poly(methyl methacrylate) modified natural rubber,” European Polymer Journal, vol. 107, pp. 132-142, 2018.

P. Intharapat, D. Derouet, and C. Nakason, “Thermal and flame resistance properties of natural rubber-g-poly(dimethyl(methacryloyloxymethyl)phosphonate),” Journal of Applied Polymer Science, vol. 115, pp. 255-262, 2010.

B. Sripornsawat, C. Nakason, and A. Keasaman, “Effect of modified natural rubber on properties of thermoplastic natural rubber based on Co-polyamide blends,” Advanced Materials Research, vol. 626, pp. 233-236, 2013.

S. Pichaiyut, C. Nakason, C. Kummerlowe, and N. Vennemann, “Thermoplastic elastomers based on epoxidized natural rubber/ thermoplastic polyurethane blends: influence of blending technique,” Polymers for Advanced Technologies, vol. 23, pp. 1011-1019, 2012.

H. M. Li, H. B. Chena, Z. G. Shenb, and S. Linb, “Preparation and characterization of maleic anhydride-functionalized syndiotactic polystyrene,” Polymer, vol. 43, pp. 5455- 5461, 2002.

M. Narathichat, C. Kummerlowe, N. Vennemann, and C. Nakason, “Thermoplastic natural rubber based on polyamide-12: influence of blending technique and type of rubber on temperature scanning stress relaxation and other related properties,” Journal of Applied Polymer Science, vol. 121, pp. 805-814, 2011.

N. Vennemann, K. Bokamp, and D. Broker, “Crosslink density of peroxide cured TPV,” Macromolecular Symposia, vol. 245, pp. 641- 650, 2006.

A. Barbe, K. Bokamp, C. Kummerlowe, H. Sollmann, and N. Vennemann, “Investigation of modified SEBS-based thermoplastic elastomers by temperature scanning stress relaxation measurements,” Polymer Engineering & Science, vol. 45, pp. 1498-1507, 2005.

Downloads

Published

2019-09-30

How to Cite

[1]
S. Saiwari, B. Sripornsawat, and N. . Hayeemasae, “Novel thermoplastic vulcanizates based on polyamide 12 blends: Influence of modified devulcanized natural rubber gloves on properties of the blends”, J Met Mater Miner, vol. 29, no. 3, Sep. 2019.

Issue

Section

Original Research Articles

Most read articles by the same author(s)