Study on mechanical and viscoelastic behavior of carbon nanotube (CNT) reinforced Epofine1564 nanocomposite

Authors

  • Puneet Kumar National Institute of Technology Rourkela, India
  • Jonnalagadda Srinivas Department of Mechanical Engineering, National Institute of Technology Rourkela, Odisha

DOI:

https://doi.org/10.55713/jmmm.v29i4.512

Keywords:

MWCNTs, Solution mixing, Bending, Tensile, Impact, Viscoelastic behavior

Abstract

This paper presents an experimental study to examine the mechanical and viscoelastic characteristics of multi-walled carbon nanotubes (MWCNTs) reinforced epoxy nanocomposite. The nanocomposite samples of varying volume fractions are prepared using solution mixing technique. A two-step mixing procedure with magnetic stir and bath type ultra sonicator is employed to acquire well dispersion of CNTs in epoxy resin. Three-point bending, tensile and impact tests are conducted on the prepared samples to measure the elastic modulus, strength and failure strain respectively. The morphological analysis of fractured samples is carried-out under field emission scanning electron microscopy (FESEM). The dispersion and reinforcing mechanism of CNTs within the polymer matrix are observed. The results show that a small amount of CNTs in a polymer matrix improves the stiffness and strength of the composite considerably. The agglomeration occurs beyond the 0.5 wt% of CNTs. Furthermore, towards thermal stability analysis, the improvement of viscoelastic characteristics with the addition of MWCNTs is studied using dynamic mechanical analysis test. Results are shown in the form of graphs and tables.

Downloads

Download data is not yet available.

Author Biographies

Puneet Kumar, National Institute of Technology Rourkela, India

Reserach Scholar

NIT Rourkela

Jonnalagadda Srinivas, Department of Mechanical Engineering, National Institute of Technology Rourkela, Odisha

Professor

Department of Mechanical engineering

National Institute of Technology Rourkela

References

Q. Jiang, X. Wang, Y. Zhu, D. Hui, and Y. Qiu, “Mechanical, electrical and thermal properties of aligned carbon nanotube/polyimide composites,” Composite Part B: Engineering, vol. 56, pp. 408-412, 2014.

R. Andrews, D. Jacques, D. Qian, and T. Rantell, “Multiwall carbon nanotubes: synthesis and application,” Accounts of Chemical Research, vol. 35(12), pp. 1008-1017, 2002.

M. Arroyo and T. Belytschko, “Continuum mechanics modeling and simulation of carbon nanotubes,” Meccanica, vol. 40(4-6), pp. 455- 469, 2005.

P. Kumar and J. Srinivas, “Numerical evaluation of effective elastic properties of CNT-reinforced polymers for interphase effects,” Computational Materials Science, vol. 88, pp. 139-144, 2014.

F. H. Gojny, M. H. G. Wichmann, U. Köpke, B. Fiedler, and K. Schulte, “Carbon nanotube reinforced epoxy-composites: enhanced stiffness and fracture toughness at low nanotube content,” Composite Science and Technology, vol. 64(15), pp. 2363-2371, 2004.

Q. Cheng, J. Wang, K. Jiang, Q. Li, and S. Fan, “Fabrication and properties of aligned multiwalled carbon nanotube-reinforced epoxy composites,” Journal of Material Research, vol. 23(11), pp. 2975-2983, 2008.

M. R. Loos, L. A. F. Coelho, S. H. Pezzin, and S. C. Amico, “Effect of carbon nanotubes addition on the mechanical and thermal properties of epoxy matrices,” Materials Research, vol. 11(3), pp. 347-352, 2008.

J. S. Puneet Kumar, “Three phase composite cylinder assemblage model for analyzing the elastic behavior of MWCNT-reinforced polymers,” Computers Materials and Continua, vol. 54(1), pp. 1-20, 2018.

S. O. Gajbhiye and S. P. Singh, “Experimental investigation of static and dynamic characteristics of multiwall carbon nanotubes reinforced polypropylene,” Applied Mechanics and Materials, vol. 592-594, pp. 927-931, 2014.

S. Singh, V. K. Srivastava, and R. Prakash, “Influences of carbon nanofillers on mechanical performance of epoxy resin polymer,” Applied Nanoscience, vol. 5(3), pp. 305-313, 2015.

P. Jindal, M. Goyal, and N. Kumar, “Mechanical characterization of multiwalled carbon nanotubes- polycarbonate composites,” Materials & Design, vol. 54, pp. 864-868, 2014.

M. Le Wu, Y. Chen, L. Zhang, H. Zhan, L. Qiang, and J. N. Wang, “High-Performance Carbon Nanotube/Polymer Composite Fiber from Layer-by-Layer Deposition,” ACS Applied Materials and Interfaces, vol. 8(12), pp. 8137- 8144, 2016.

G. V. Ramana, B. Padya, R. N. Kumar, K. V. P. Prabhakar, and P. K. Jain, “Mechanical properties of multi-walled carbon nanotubes reinforced polymer nanocomposites,” Indian Journal of Engineering and Materials Science, vol. 17(5), pp. 331-337, 2010.

F. Vahedi, H. R. Shahverdi, M. M. Shokrieh, and M. Esmkhani, “Effects of carbon nanotube content on the mechanical and electrical properties of epoxy-based composites,” New Carbon Materials, vol. 29, pp. 419-425, 2014.

S. Kapoor, M. Goyal, and P. Jindal, “Effect of multi-walled carbon nanotubes (MWCNT) on mechanical properties of acrylonitrile butadiene styrene (ABS) nano-composite,” Indian Journal of Science and Technology, vol. 10(17), pp. 1-6, 2017.

S. Bansal, N. Kumar, and P. Jindal, “Effect of MWCNT composition on the hardness of PP/MWCNT composites,” Materials Today: Proceedings, vol. 4, pp. 3867-3871, 2017.

E. Fontananova, V, Grosso, S. A. Aljlil, M. A. Bahattab, D. Vuono, F. P Nicoletta, E. Curcio, E. Drioli, and G. D. Profio, “Effect of functional groups on the properties of multiwalled carbon nanotubes/polyvinylidenefluoride composite membranes,” Journal of Membrane Science, vol. 541, pp. 198-204, 2017.

A. E. Moumen, M. Tarfaoui, H. Benyahia, and K. Lafdi, “Mechanical behavior of carbon nanotubes-based polymer composites under impact tests,” Journal of Composite Materials, vol. 0(0), pp.1-16, 2018.

S. Saha and S. Bal, “Influence of nanotube content on the mechanical and thermomechanical behaviour of –COOH functionalized MWNTs/epoxy composites,” Bulletin of Materials Science, vol. 40(5), pp. 945-956, 2017.

L. Liu, Y. Zhou, and S. Pan, “Experimental and analysis of the mechanical behaviors of multiwalled nanotubes/polyurethane nanowebreinforced epoxy composites,” Journal of Reinforced Plastics and Composites, vol. 32(11), pp. 823-834, 2013.

M. Lee, T. Koo, S. Lee, B. H. Min, and J. H. Kim, “Morphology and physical properties of nanocomposites based on poly(methyl methacrylate)/poly(vinylidene fluoride) blends and multiwalled carbon nanotubes,” Polymer Composites, vol. 36(7), pp. 1195-1204, 2015.

J. Yang, Z. Zhang, K. Friedrich, and A. K. Schlarb, “Creep resistant polymer nanocomposites reinforced with multiwalled carbon nanotubes,” Macromolecular Rapid Communications, vol. 28(8), pp. 955-961, 2007.

A. Plaseied and A. Fatemi, “Tensile creep and deformation modeling of vinyl ester polymer and its nanocomposite,” Journal of Reinforced Plastics and Composites, vol. 28(14), pp. 1775- 1788, 2009.

Y. Jia, K. Peng, X. Gong, and Z. Zhang, “Creep and recovery of polypropylene/carbon nanotube composites,” International Journal of Plasticity, vol. 27(8), pp. 1239-1251, 2011.

J. Suhr, N. Koratkar, P. Keblinski, and P. Ajayan, “Viscoelasticity in carbon nanotube composites,” Nature Materials, vol. 4(2), pp. 134-137, 2005.

Y. Pan, G. J. Weng, S. A. Meguid, W. S. Bao, Z. H. Zhu, and A. M. S. Hamouda, “Interface effects on the viscoelastic characteristics of carbon nanotube polymer matrix composites,” Mechanics of Materials, vol. 58, pp. 1-11, 2013.

P. Kumar and J. Srinivas, “Elastic and thermal property studies of CNT reinforced epoxy composite with waviness, agglomeration and interphase effects,” International Journal of Material Engineering Innovation, vol. 9(2), pp. 158-177, 2018.

N. Saba, A. Safwan, M. L. Sanyang, F. Mohammad, M. Pervaiz, M. Jawaid, O. Y. Alothman, M. Sain, “Thermal and dynamic mechanical properties of cellulose nanofibers reinforced epoxy composites.,” International Journal of Biological Macromolecules, vol. 102, pp. 822-828, 2017.

Downloads

Published

2019-12-26

How to Cite

[1]
P. Kumar and J. . Srinivas, “Study on mechanical and viscoelastic behavior of carbon nanotube (CNT) reinforced Epofine1564 nanocomposite”, J Met Mater Miner, vol. 29, no. 4, Dec. 2019.

Issue

Section

Original Research Articles